Dovetail joints are the gold standard of woodworking joinery, and the choice between English and French dovetails can make or break a project. English dovetails, with their half-blind pins and tails, are the workhorse for drawer fronts, while French dovetails, also known as sliding dovetails, offer a sleek, interlocking slot-and-tongue joint perfect for shelves and casework. This guide breaks down the differences, strengths, and step-by-step instructions for cutting both, so you can choose the right joint for your next piece.
Ingredients
- Hardwood stock for pins and tails (e.g., oak, walnut, cherry) – 2 pieces, each 3/4 in (19 mm) thick, 4 in (102 mm) wide, 12 in (305 mm) long
- Dovetail saw (or fine-toothed backsaw) – 1
- Chisels (1/4 in / 6 mm and 1/2 in / 12 mm) – 1 each
- Marking gauge – 1
- Dovetail marker (1:6 or 1:8 slope) – 1
- Coping saw or fret saw – 1
- Mallet – 1
- Pencil or marking knife – 1
- Wood glue (e.g., Titebond II) – 2 oz (60 ml)
- Clamps (bar or pipe clamps) – 2
- Optional: router with dovetail bit (for French dovetail) – 1
Instructions
- Prepare the stock: Mill both boards to final thickness (3/4 in / 19 mm) and cut them to length. Ensure the ends are square and the faces are flat. Mark the outside faces with a pencil to avoid confusion.
- Lay out the English dovetail tails: On one board (the tail board), use a marking gauge to scribe a line at the thickness of the other board (3/4 in / 19 mm) from the end. Using a dovetail marker (1:6 slope for softwood, 1:8 for hardwood), mark the tails on the end grain. Space them evenly, with half-pins at the edges. Extend the lines down the face to the gauge line.
- Cut the tails (English): Clamp the tail board vertically in a vise. With a dovetail saw, cut along the waste side of each marked line, stopping precisely at the gauge line. Do not overcut. Then, use a coping saw to remove the waste between the tails, cutting close to the gauge line. Clean up the sockets with a chisel, paring to the line.
- Transfer tails to pin board (English): Place the tail board on top of the pin board, aligning the ends. Use a marking knife to trace the tails onto the pin board. Extend these lines down the face of the pin board to the gauge line (scribed at the thickness of the tail board).
- Cut the pins (English): Clamp the pin board vertically. Saw along the waste side of the pin lines, again stopping at the gauge line. Remove the waste between pins with a chisel, working from both sides to avoid tearout. Test-fit the joint; it should slide together with light mallet taps.
- Assemble the English dovetail: Apply wood glue to both the pins and tails. Join the pieces, tapping with a mallet until flush. Clamp and let dry for at least 1 hour.
- Lay out the French dovetail: For the French (sliding) dovetail, you will create a tapered slot in one board and a matching tapered tongue on the other. On the socket board, mark a line 1/2 in (12 mm) from the edge, and another 1/2 in (12 mm) deeper. The slot should taper from 1/2 in (12 mm) at the front to 3/8 in (10 mm) at the back. On the tongue board, mark the corresponding taper.
- Cut the socket (French): Using a router with a dovetail bit (or a chisel and saw), rout the slot to the marked depth and taper. If using hand tools, saw the sides of the slot and chisel out the waste. The slot should be clean and square at the bottom.
- Cut the tongue (French): Shape the tongue to match the taper of the slot, using a table saw, router, or hand planes. The tongue should slide into the slot with moderate resistance, requiring a mallet to drive it home.
- Assemble the French dovetail: Apply glue to the tongue and slide it into the slot. Tap with a mallet until the joint is fully seated. Clamp and let dry for at least 1 hour.
Tips
- Sharp tools are non-negotiable: Dull chisels and saws will crush the wood fibers, leading to ragged joints. Sharpen your tools before starting.
- Practice on scrap first: Dovetails require precision. Cut a few practice joints on inexpensive pine to get the hang of sawing to the line and chiseling clean sockets.
- Use a marking knife instead of a pencil: A knife cuts the fibers for a cleaner edge and gives a more accurate line than a pencil.
- For the French dovetail, a router is your friend: Hand-cutting a tapered slot is challenging. A router with a dovetail bit and a tapered guide will give you a perfect fit every time. If using hand tools, be prepared to pare slowly and test-fit often.
Serving Suggestions
Use English dovetails for drawer fronts, jewelry boxes, and any visible corner joint where you want a classic, handcrafted look. French dovetails are ideal for shelf supports, cabinet sides, and sliding lids—anywhere you need a strong, hidden joint that resists racking. Both joints are equally at home in a rustic farmhouse table or a sleek modern cabinet.
Variations
- Through dovetails: The tails and pins are both fully visible on both faces. This is the simplest dovetail to cut and is often used for carcass construction.
- Half-blind dovetails: The pins are hidden on one face (usually the front of a drawer), while the tails are visible on the side. This is what most people mean by “English dovetail.”
- Sliding dovetail with a stopped slot: Instead of a through slot, the slot stops short of the back edge, creating a hidden joint that is invisible from the front. This is common in table aprons.
- Multiple dovetail slots: For extra strength, you can cut two or more parallel French dovetails on a single board, as in a drawer bottom.
Storage and Reheating
Store your dovetailed project in a dry, climate-controlled environment to prevent wood movement. If the joint becomes loose over time, you can disassemble (if not glued) or inject wood glue and clamp. Dovetails are meant to last for generations, so no reheating needed—just occasional tightening of screws or glue if the joint loosens. For unglued joints, store them dry and flat to avoid warping.
Frequently Asked Questions
Which dovetail is stronger? Both are strong when cut properly. English dovetails excel at resisting pull-apart forces (like a drawer being yanked open). French dovetails are stronger against racking (side-to-side forces) because the interlocking slot and tongue resist twisting. For most furniture, English dovetails are the traditional choice for drawers; French dovetails are better for shelves and casework.
Can I use a router for English dovetails? Yes, but it’s tricky. A dovetail jig and router bit can cut both pins and tails, but you’ll lose the hand-cut look. Many woodworkers prefer hand-cutting for a more organic, artisanal appearance. If you want speed and precision, a router jig is a good option, but practice on scrap first.
What’s the best angle for dovetails? The slope (angle) of the tails is typically 1:6 (about 9.5°) for softwoods and 1:8 (about 7°) for hardwoods. A steeper angle (1:6) holds better in softwood because the wood is less dense; a shallower angle (1:8) is stronger in hardwood. You can use a dovetail marker to set the angle accurately.
Why are my dovetails loose? Loose dovetails usually result from cutting on the wrong side of the line or not chiseling to the exact line. Always cut on the waste side, and test-fit before gluing. If the joint is too tight, you can pare a little more. If it’s too loose, you may need to glue a thin shim, but it’s better to re-cut the joint.
Can I use plywood for dovetails? Yes, but it’s not ideal. Plywood’s layered construction can chip and tear out, especially on the edges. If you must use plywood, use a sharp blade and cut slowly. Baltic birch plywood works better than softwood plywood. For a cleaner joint, use solid wood.
How long does it take to cut dovetails by hand? For a beginner, a single English dovetail joint (one corner) can take 20-30 minutes. With practice, you can cut a drawer’s four corners in under an hour. French dovetails are faster once you set up a router, but hand-cutting a tapered slot can take 15-20 minutes per joint.
Related
- Poplar Cherry Substitute: How to Use It in Recipes
- Regular vs Tempered Hardboard: Key Differences
- Cheats Hot Chocolate Bomb Recipe
More recipes to cook
Safety notes: safe minimum internal temperatures from USDA FSIS; raw and undercooked fish guidance from the U.S. FDA. Food safety notes
Spotted an error? Tell us and we will correct it (corrections policy).