How to Make Paper Straws: A Step-by-Step Guide

Updated November 15, 2026

Jump to recipe

Paper straws are a simple, eco-friendly alternative to plastic ones, perfect for parties, everyday drinks, or craft projects. This guide walks you through making sturdy, functional paper straws at home using basic materials. You’ll need a few supplies and a little patience, but the result is a custom, biodegradable straw that’s both practical and fun to create.

What You’ll Need

  • Paper strips: 1–2 inches (2.5–5 cm) wide and 8–12 inches (20–30 cm) long. Use lightweight paper like wrapping paper, scrapbook paper, or printer paper. Avoid heavy cardstock as it’s hard to roll.
  • A thin dowel or skewer: about 1/8 inch (3 mm) in diameter, or a store-bought straw to use as a mold.
  • Non-toxic glue stick or white school glue (PVA).
  • Ruler and scissors or a paper cutter.
  • Optional: a small brush for spreading glue, and a flat surface to work on.

Step-by-Step

  1. Cut your paper strips. Use a ruler and scissors (or a paper cutter) to cut strips that are 1–2 inches (2.5–5 cm) wide and 8–12 inches (20–30 cm) long. The width determines the straw’s length, and the length determines the straw’s diameter—longer strips make thinner straws.
  2. Prepare the glue. If using a glue stick, have it ready. If using liquid glue, pour a small amount into a dish and have a brush on hand. You’ll need to work quickly, so keep everything within reach.
  3. Apply glue to the strip. Lay the paper strip flat. Apply a thin, even layer of glue along the entire strip, leaving about 1/2 inch (1.3 cm) at one end unglued. This unglued flap will help seal the straw at the end.
  4. Start rolling. Place the dowel or skewer at one of the short ends of the strip, parallel to the edge. Begin rolling the paper around the dowel, keeping it tight and even. Roll slowly to avoid wrinkles or air bubbles.
  5. Continue rolling. Roll the paper all the way to the other end, maintaining even tension. The unglued flap should be at the very end, and you’ll glue it down to seal the straw.
  6. Seal the edge. Once you reach the end, apply a bit more glue to the unglued flap and press it firmly against the rolled tube. Hold it in place for a few seconds to ensure it sticks.
  7. Slide the straw off the dowel. Gently twist the dowel while pulling the straw off. If it’s stuck, roll the dowel back and forth a little to loosen the paper.
  8. Let it dry. Place the finished straw on a flat surface to dry completely. This may take 15–30 minutes depending on the glue and humidity. For best results, let it dry overnight.
  9. Trim the ends (optional). Once dry, use scissors to trim the ends of the straw to make them even and neat.

Common Mistakes

  • Using too much glue: Excess glue makes the paper soggy and difficult to roll. Use a thin, even layer.
  • Rolling too loosely: A loose roll creates a flimsy straw that collapses easily. Keep the paper taut as you roll.
  • Paper too thick: Heavy paper like cardstock is hard to roll and may crack. Stick to lightweight paper.
  • Not letting it dry fully: Using a wet straw will cause it to bend or disintegrate in your drink. Patience is key.
  • Uneven cutting: If your strips are not straight, the straw will have a crooked shape. Measure and cut carefully.

Tips

  • Use patterned paper: Wrapping paper or scrapbook paper adds a festive touch. Just make sure it’s not too thick.
  • Make a batch: Roll several straws at once to save time. They store well in a jar or container.
  • Waterproofing: For extra durability, you can coat the finished straw with a thin layer of beeswax or a food-safe sealant. This helps it resist moisture longer.
  • Experiment with widths: For smoothies or thicker drinks, use a wider strip (2 inches / 5 cm) to create a wider straw. For cocktails, a narrower strip works.
  • Use a straw as a mold: If you have a store-bought paper straw, you can use it as a rolling mold instead of a dowel. This ensures a consistent diameter.

Troubleshooting

  • Straw is too tight to slide off the dowel: If the straw sticks, gently roll the dowel back and forth on a flat surface to loosen the paper. If it’s still stuck, try using a thinner dowel next time, or apply a little cooking spray to the dowel before rolling.
  • Straw is too flimsy: This usually means the paper was rolled too loosely. Unroll and start again with tighter tension. You can also use a slightly thicker paper, but avoid cardstock.
  • Straw collapses when used in a drink: The straw may not be fully dry, or the paper is too thin. Ensure it’s completely dry before using. For a sturdier straw, use two layers of paper: roll one layer, then glue another strip around it.
  • Glue doesn’t stick: Some glues (like glue sticks) may not adhere well to glossy paper. Use liquid glue or a stronger adhesive. Also, make sure the paper is clean and dry.
  • Edges are frayed: If your paper tears while rolling, the strip might have nicks. Cut a fresh strip and try again, being careful to cut cleanly.

Frequently Asked Questions

Can I use regular printer paper? Yes, printer paper works well. It’s lightweight and easy to roll. Just be aware that it’s not very absorbent-resistant, so it may get soggy faster than coated paper.

How long does a homemade paper straw last in a drink? Typically, a homemade straw will last about 30–60 minutes in a cold drink before it starts to soften. Using a waterproofing coating can extend that time.

Can I make paper straws without a dowel? Yes, you can use a pencil, a chopstick, or even a store-bought straw as a rolling mold. The key is to have a cylindrical object that’s slightly larger than the final straw’s inner diameter.

What kind of glue is safe for food contact? Use non-toxic, food-safe glue. White school glue (like Elmer’s) is non-toxic and generally considered safe, but it’s not meant to be eaten. For a more food-safe option, use a glue made from natural ingredients like flour paste or a food-grade adhesive.

Can I compost my homemade paper straws? Yes, since they are made of paper and non-toxic glue, they are compostable. Just remove any waterproofing coating if you applied one, as some coatings may not be compostable.

How do I make wider straws for smoothies? Use a wider strip of paper (2–3 inches / 5–7.5 cm) and a thicker dowel (about 1/4 inch / 6 mm). This will create a straw with a larger diameter, perfect for thick drinks.

Related

More recipes to cook

Safety notes: safe minimum internal temperatures from USDA FSIS; raw and undercooked fish guidance from the U.S. FDA. Food safety notes

Spotted an error? Tell us and we will correct it (corrections policy).