Brazilian Cherry Bar Oak Entertainment Center

Updated November 15, 2026

Total time
6 hr
prep 3 hr · cook 0 min
Serves
1
one portion

Jump to recipe

This isn’t a dish you eat—it’s a DIY furniture project that brings the rich, warm tones of Brazilian cherry wood (also known as jatobá) and the classic appeal of oak into your living space. This entertainment center combines a built-in bar area with ample storage for media components, making it both a functional centerpiece and a stylish conversation starter. With clear steps and practical tips, you’ll build a sturdy, beautiful piece that fits your home and your entertainment needs.

Ingredients

  • 1 sheet (4′ x 8′) 3/4″ (19 mm) birch plywood (for carcass and shelves)
  • 1 sheet (4′ x 8′) 1/2″ (12 mm) oak plywood (for back panel and drawer bottoms)
  • 8 board feet of 4/4 (1″ thick) Brazilian cherry (jatobá) lumber (for face frame, doors, and trim) – or use 1″ (25 mm) solid oak as a substitute
  • 1 sheet (4′ x 8′) 1/4″ (6 mm) oak plywood (for drawer sides and interior dividers)
  • 4 pairs of soft-close drawer slides (22″ / 560 mm full extension)
  • 6 pairs of soft-close cabinet hinges (for doors)
  • 2 sets of adjustable shelf pins (at least 24 pins)
  • 1 bottle of wood glue (PVA, waterproof)
  • 1 box of 1-1/4″ (32 mm) pocket hole screws
  • 1 box of 1″ (25 mm) brad nails
  • 4 adjustable feet (leveling legs) – rated for 250 lbs (113 kg) each
  • Wood filler (color-matched to cherry or oak)
  • Sandpaper: 80, 120, 220 grit
  • Finish: 2 coats of polyurethane (satin or semi-gloss) or Danish oil
  • Optional: 1 bottle of wood conditioner (if using oil-based stain)

Instructions

  1. Cut the plywood panels. Using a table saw or circular saw with a straight edge, cut the 3/4″ birch plywood into the following pieces: two side panels (24″ x 72″ / 61 x 183 cm), top and bottom panels (24″ x 48″ / 61 x 122 cm), two fixed shelves (24″ x 48″ / 61 x 122 cm), and two adjustable shelves (23″ x 48″ / 58 x 122 cm). Cut the 1/2″ oak plywood into a back panel (48″ x 72″ / 122 x 183 cm) – you may need to join two pieces if your sheet is smaller; use a biscuit joiner or a simple butt joint with glue and screws.
  2. Cut the Brazilian cherry lumber. For the face frame, cut four stiles (vertical pieces) at 2″ x 72″ (5 x 183 cm) and three rails (horizontal pieces) at 2″ x 44″ (5 x 112 cm). For the doors, cut four door panels at 18″ x 30″ (46 x 76 cm) and four door frames (stiles and rails) – or simply use full 1″ thick cherry boards for a slab door style. For the trim, cut two pieces at 1″ x 72″ (2.5 x 183 cm) and two at 1″ x 48″ (2.5 x 122 cm).
  3. Assemble the carcass. Apply wood glue to the edges of the top, bottom, and fixed shelves. Attach them to the side panels using pocket holes drilled in the sides (or use dowels and clamps). Ensure the fixed shelves are placed to create a lower media compartment (about 24″ / 61 cm high) and an upper bar area (about 20″ / 51 cm high). Clamp and let dry for 1 hour.
  4. Install the back panel. Lay the carcass face down. Apply glue to the back edges and place the 1/2″ oak plywood back panel. Secure with brad nails every 6 inches (15 cm). This will square the cabinet. Let dry for 30 minutes.
  5. Attach the face frame. Glue and nail (or pocket screw) the stiles and rails to the front edges of the carcass. Make sure the frame is flush with the front. Use clamps and let dry for 1 hour.
  6. Build the drawers. For each drawer, cut two sides (6″ x 20″ / 15 x 51 cm) and front/back (6″ x 22″ / 15 x 56 cm) from 1/4″ oak plywood. Assemble with glue and brad nails. Attach the drawer fronts (cut from cherry or oak, 8″ x 24″ / 20 x 61 cm) after the slides are installed.
  7. Install drawer slides and drawers. Mount the slides on the inside of the carcass (in the lower media compartment) and on the drawer sides. Follow the manufacturer’s instructions for spacing. Slide the drawers in and adjust the fronts for a uniform gap.
  8. Build and hang the doors. For each door, assemble the frame (stiles and rails) around the cherry panel, using glue and clamps. Let dry. Attach hinges to the doors and then to the face frame. Adjust the hinges for a perfect fit.
  9. Add adjustable shelves. Drill 1/4″ (6 mm) holes in the side panels at 1-inch intervals (or use a shelf pin jig) in the upper bar area and media compartment. Insert shelf pins and place the adjustable shelves.
  10. Install the trim and feet. Attach the 1″ cherry trim to the top and bottom edges of the carcass using glue and brad nails. Screw the adjustable feet into the bottom corners, ensuring they are level.
  11. Sand and finish. Sand the entire piece with 120-grit, then 220-grit. Wipe off dust. Apply wood conditioner if using stain (not needed if you’re using a clear finish). Apply two coats of polyurethane or Danish oil, sanding lightly with 220-grit between coats. Let dry completely (2 hours between coats, 24 hours before use).
  12. Install hardware. Attach knobs or pulls to the doors and drawers. Install any optional interior lighting (e.g., LED strip lights) in the bar area.

Tips

  • Substitutions: If Brazilian cherry is hard to find or too expensive, use solid oak for the face frame and doors. The color will be lighter, but you can apply a cherry-toned stain to mimic the deep red-brown hue. Alternatively, use cherry veneer plywood for the entire carcass to simplify the build.
  • Storage: This is a permanent piece, so no food storage applies. For wood care, keep it away from direct sunlight to prevent fading, and use coasters under drinks to avoid water rings.
  • Common mistake: Not accounting for the thickness of the face frame when cutting doors and drawers. Always measure the opening after the frame is installed, then subtract 1/8″ (3 mm) on all sides for a 1/4″ (6 mm) gap.
  • Safety: Always wear safety glasses and hearing protection when using power tools. Use a push stick when cutting narrow pieces on the table saw.

Serving Suggestions

This entertainment center is designed to host. The bar area can hold a coffee machine, a selection of spirits, and glassware. Pair it with a comfortable sofa and a large-screen TV. For a complete home theater setup, add a soundbar on the media shelf and store remotes in the drawers. The cherry wood’s warm tones complement leather furniture and earth-toned decor.

Variations

  • Wine Rack: Convert one of the adjustable shelves into a wine rack by installing a metal wine bottle holder or building a wooden grid with 3.5″ (9 cm) squares.
  • Glass Door Display: Replace the solid cherry door panels with glass (using a router to create a rabbet) to display collectibles or barware.
  • LED Lighting: Add LED strip lights under the shelves and inside the bar area to highlight your collection. Use a motion sensor or remote for convenience.
  • Open Shelving: Skip the doors entirely for an open-concept look, which is easier to build and great for a modern aesthetic.

Storage and Reheating

Since this is furniture, there’s no reheating. To keep it looking new, dust weekly with a soft cloth. For deeper cleaning, use a wood-safe cleaner and a damp (not wet) cloth. Avoid harsh chemicals. If scratches appear, lightly sand with 220-grit and apply a fresh coat of polyurethane. The piece is built to last for decades with proper care.

Frequently Asked Questions

How long does this project take? Expect a full weekend: about 6 hours of active work plus drying time. If you’re a beginner, plan for 8-10 hours.

Can I use only plywood and skip the solid wood? Yes, you can use cherry veneer plywood for the face frame and doors. It’s easier and cheaper, but the edges will show plywood layers unless you edge-band them with iron-on veneer.

What tools do I absolutely need? A table saw (or circular saw with a guide), a drill/driver, a pocket hole jig (or dowel jig), clamps, and a sander. A router is helpful for door panels but not essential if you use slab doors.

How do I make sure the cabinet is square? Measure diagonally from corner to corner; the two measurements should be equal. Adjust clamps before the glue dries.

Can I paint the oak instead of staining? Absolutely. Oak takes paint well, but you’ll need to prime first. Brazilian cherry is oily and may bleed through paint, so it’s best to stick with clear finishes or use a shellac-based primer.

What if my wall isn’t level? Use the adjustable feet to level the cabinet. If it’s against a wall, you can also shim the base and attach it to the wall with furniture anti-tip straps for safety.

Related

More recipes to cook

Safety notes: safe minimum internal temperatures from USDA FSIS; raw and undercooked fish guidance from the U.S. FDA. Food safety notes

Spotted an error? Tell us and we will correct it (corrections policy).